[QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Vše ohledně QNAP firmwarů "QTS, QuTS hero, QES a QuRouter" - stabilní i beta verze.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "1.7.8.0001 build 20210917".

Nová verze je k dispozici v menu QHora routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Důležité poznámky
  • To add the router to the QuWAN network, users must bind their QNAP ID in the QuWAN Settings page or log in to QuRouter with their QNAP ID.
QuWAN -> QuWAN Settings -> Log in with QNAP ID
Obrázek

Nové vlastnosti
  • Added support for IPv6 in WAN, VLAN, and static route settings.
  • Added support for MTU in VLAN settings.
  • Added the WAN IP attribute feature in QuWAN settings: Public IP, Behind NAT, Behind NAT (Device role - Hub or edge), Public IP (IPSec / IKE passthrough failure)
  • Users can reset the local account and password by pressing the reset button for 5 seconds, and reset the router settings to default settings by pressing the reset button for 10 seconds.
IPv6 in WAN
Obrázek

IPv6 in VLAN
Obrázek

IPv6 in Static Route
Obrázek

MTU on VLAN
Obrázek

Vylepšení
  • Modified several user interface strings and the user interface workflow in the QuRouter user interface.
  • QuRouter prompts the users to specify a strong pre-shared key when configuring the VPN server settings.
  • Added access and trunk mode description in the WAN & LAN Settings page.
  • Users can specify the primary and secondary DNS IP address in two different fields when configuring the WAN port settings in the WAN & LAN Settings page.
  • If there are no user accounts created in QuRouter, users are reminded to create a VPN user account in the QVPN User Management page when they access the QVPN Settings page in the QVPN Server section.
Network -> WAN & LAN Settings -> LAN Settings
Obrázek

Network -> WAN & LAN Settings -> WAN Settings
Obrázek

QVPN Servers -> QVPN Settings
Obrázek

Opravené chyby
  • Due to myQNAPcloud retry interval issues, users could not access the internet for 24 hours after enabling DDNS (MyDDNS) and changing the WAN IP address in QuRouter.
  • QuRouter would allow users to enter an MTU value less than 576 bytes in the WAN settings page.
  • QuRouter would display an incoherent message if users added a VLAN in the VLAN & DHCP Server Service Settings page.
  • Users were unable to access the internet via LAN trunk mode after adding the router to the QuWAN network.
  • When the WAN connection is configured using PPPoE settings, QuRouter would not display the external FTP link in the USB Settings page.
  • Users could not disable the "Local management via HTTP" setting when the device is in access point (AP) mode.
  • Users could not perform firmware checks and update the firmware version using the "Live Update" function in the QuRouter Firmware page when the device is in access point (AP) mode.
  • QuRouter would display a "TOKEN_IS_EXPIRED" error message when configuring the router WAN connection with PPPoE settings during the router initialization process.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "1.8.3.0001 build 20211129".

Nová verze je k dispozici v menu QHora routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • We have improved the overall QuWAN VPN tunnel stability.
  • Users can now edit the router name in the QuWAN Settings page after logging in with their QNAP ID.
  • QuRouter retains the router session cache even after the user reaches the maximum interface session limit.
Opravené chyby
  • When configuring a device role from hub to edge in QuWAN the IPSec service port number automatically changes from 4500 to a port number between 61xxx-62xxx. We have resolved an issue where the IPSec service port number would not automatically change back to 4500 when reconfiguring the edge to hub, which would result in VPN tunnel connection failure.
  • Clients occasionally could not connect to the wireless connection of the router after enabling and configuring the wireless scheduler.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "1.8.4.0001 build 20211216".

Nová verze je k dispozici v menu QHora routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • We have improved the load balancing mechanism for dual WAN mode performance.
  • With dual WAN mode, when your current WAN connection fails, the router continues to work by automatically switching to the alternative WAN network.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "1.8.6.0001 build 20220107".

Nová verze je k dispozici v menu QHora routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • We have optimized the router ' s QuWAN VPN tunnel stability.
  • We have enhanced the OpenVPN and QBelt VPN connection stability.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "2.0.6.001 build 20220210".

Nová verze je k dispozici v menu QHora routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Nové vlastnosti
  • USB packet capture: You can now capture and transfer network traffic packets from the router to any connected USB device for data analysis.
    Obrázek
  • We have added a diagnostic tool feature that supports ping and traceroute functions to troubleshoot network access problems.
  • Ping uses Internet Control Message Protocol (ICMP) echo messages to determine host status, round-trip delay, and packet loss.
  • Traceroute identifies the path that packets take to reach their destination.
  • Users can now reconnect the PPPoE connection after a session has been terminated using the "Reconnect" button.
  • We have added support for the following: NordVPN for QVPN clients using OpenVPN, WireGuard protocol in QVPN Settings
    Obrázek
Vylepšení
  • We have improved the user interface of the QVPN Settings and QVPN User Management page in the QVPN Servers section.
  • We have enhanced the performance of the QuWAN VPN tunnel connections.
  • Optimized the QMiro-201W and QMiroPlus-201W mesh network performance.
Opravené chyby
  • We have resolved an issue where if a device is blocked using QuRouter, other devices in the same VLAN subnet were still able to ping and get a response from the blocked device.
  • Previously, when a router is configured as an Access Point (AP), QuRouter would occasionally display a network error message. We have resolved this issue.
  • We have resolved an issue where users could not change the IKE and IPSec service port numbers to 500 and 4500 respectively after configuring the router as a QuWAN device.
  • After changing the device name in QuRouter, myQNAPcloud would display the old device name. We have fixed this issue.
  • After configuring the initial QuRouter settings, the QVPN Settings page would occasionally display a network error message.
  • We have resolved a couple of issues in the port forwarding section where QuRouter would not allow the "Allow Remote IPs" field to be blank, and the port forwarding rule could not be applied occasionally.
  • After updating the firmware, QuRouter would display an incorrect message asking users if they want to exit the page without applying changes. With this update, this bug is fixed.
  • Resolved an issue where QuRouter would display only one DNS IP address after acquiring two IP addresses from two DNS servers.
  • We have fixed an issue where QuRouter would display the UI strings incompletely.
    QHora-301W
  • Previously, when an Android or iOS mobile device is connected to the router's VPN using L2TP protocol, users could not access the internet and devices in the router's LAN subnet. We have resolved this issue.
    QMiro-201W and QMiroPlus-201W
  • After configuring a mesh network using a LAN DHCP subnet, the connected nodes could not obtain renewed IP addresses. This would cause the nodes to disconnect from the primary router.
Zdroj: https://www.qnap.com/cs-cz/release-note ... 1/20220210
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W a QMiro-201W / QMiroPlus-201W s označením "2.0.7.0001 build 20220310".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • We have improved the QVPN client performance.
Opravené chyby
  • Fixed an issue where after updating QuRouter to version 2.0.6, QuRouter would not display the WAN port configuration occasionally.
  • After updating QuRouter to the latest version, the Event Logs page would display a log informing users that a new firmware version is available for download. With this update, the bug has been fixed.
  • We have resolved an issue where after updating QuRouter, the Event Logs page would not display any logs related to the firmware update.
QHora-301W
  • Previously, if the gateway on the end-user device did not frequently response to the ARP requests, the router would assume that the WAN is unavailable and clear the default gateway settings.
QMiro-201W/QMiroPlus-201W
  • QuRouter would display an "Invalid request body" error and could not join the SD-WAN service, if the user removed the router from QuWAN and attempted to add the router to the QuWAN organization again.
Zdroj: https://www.qnap.com/cs-cz/release-note ... 1/20220310
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W a QMiro-201W s označením "2.1.5.001 build 20220509".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • QHora-301W now supports QuWAN QBelt VPN server settings.
  • QuRouter can now support MAP-E and DS-Lite technology in Japan for users utilizing the "Internet Multifeed" service.
  • We have improved the overall readability of QuRouter event logs.
  • We have increased the number of DHCP reservations in QuRouter to 128 IP assignments.
  • Previously, after restoring the router settings, QuRouter would automatically change the port forwarding rule and remote users were unable to access the QuRouter interface. With this release, remote users will no longer lose connection to the router after router restoration.
Opravené chyby
  • We have resolved an issue where QNAP Remote Support would display a login failure message if the session login token expired. With this release, users will be asked to log in again when the token expires.
  • We have resolved an issue where QuRouter would display an incorrect message after establishing a PPPoE WAN connection.
QMiro-201W/QMiroPlus-201W
  • We have resolved an issue where the QuRouter dashboard would not automatically update the number of clients when a new device would connect to the router through a wireless connection.
  • Fixed an issue where blocked clients could still access QuRouter using a wireless connection. With this release, blocked clients can no longer access QuRouter.
Zdroj: https://www.qnap.com/cs-cz/release-note ... 1/20220509
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W a QMiro-201W s označením "2.1.7.013 build 20220708".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • QuRouter is now compatible with the updated QuWAN API.
Opravené chyby
  • Fixed an issue where the network speed would reduce if the network connection for the port is PPPoE.
  • Fixed an issue where IPv6 clients on QHora-301W could not correctly establish WAN communications.
  • Resolved an issue where Mac PCs could not ping the destination IP address specified in the static route page.
  • Fixed an issue where QuRouter would ask users to load the web page due to an unexpected error when users would open the NAT page.
  • Resolved an issue where QuRouter would display a blank message after configuring port forwarding rules.
  • Fixed an abnormal LED behavior issue in QHora-301W and QMiro-201W when the CPU temperature would reach 85°C.
  • Fixed an issue where QuRouter would generate the CPU overheating event log every 10 seconds. With this update, you will no longer see the same recurring event log in QHora-322.
QMiroPlus-201W
  • Fixed an issue where QuRouter login token would expire after powering on the router.
  • Resolved an issue where the QTS name would not be displayed on the QuRouter Dashboard page. This would occur only after rebooting the device following the router initialization.
Zdroj: https://www.qnap.com/cs-cz/release-note ... 3/20220708
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W s označením "2.1.8.020 build 20220817".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • QuRouter can now re-establish the HelpDesk SSH tunnel automatically after rebooting the router.
  • Improved the UI in the parental role rules page.
  • Improved the Address Resolution Protocol (ARP) ping mechanism to prevent the router from disconnecting from ISP devices.
  • Increased the maximum number of concurrent DNS queries.
Opravené chyby
  • Fixed an issue where QuRouter would display the incorrect time for event logs.
  • Resolved an issue where the DDNS connection would automatically disconnect when the WAN interface connection is interrupted.
  • Added an alert message to notify users in case they use the same IP address for the default gateway and fixed IP address.
  • Fixed an issue where QuRouter would incorrectly inform users the PPPoE did not reconnect even though the PPPoE connection was established.
  • Users were unable to add the router to QuWAN Orchestrator if static route settings were configured prior to adding the router to the cloud SD-WAN platform.
Uživatelský avatar
lars
Příspěvky: 2049
Registrován: 21 říj 2015, 21:43
Kontaktovat uživatele:

Re: [QuRouter, finální verze] QuRouter (fw) pro router QHora-301W

Příspěvek od lars »

Vyšel nový firmware pro QNAP router QHora-301W a a QMiro-201W s označením "2.1.10.001 build 20220922".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • Improved the WAN IP addressing mechanism.
Opravené chyby
  • Previously, QuRouter would freeze when the host device is connected to the network using a PPPoE connection for a prolonged period. Users would have to reboot the router to fix this issue. With this release, this bug has been fixed.
  • Fixed an issue where users could not ping and access QuWAN clients after establishing a VPN connection through QBelt VPN server on QuWAN vRouter.
  • Fixed a user interface string related to online connected clients in the Clients page.
  • Resolved an issue where the host device would disconnect from QuWAN Orchestrator if the web framework of the device malfunctions.
-----------------------------

Vyšel nový firmware pro QNAP router QHora-321 a QHora-322 s označením "2.2.5.002 build 20220928".

Nová verze je k dispozici v menu routeru - sekce Firmware, nebo je možné jej stáhnout i na webové stránce "Centrum stahování".

Vylepšení
  • Improved the WAN IP addressing mechanism of the router.
Opravené chyby
  • Previously, QuRouter would freeze when the host device is connected to the network using a PPPoE connection for a prolonged period. Users would have to reboot the router to fix this issue. With this release, this bug has been fixed.
  • Fixed an issue where users could not ping and access QuWAN clients after establishing a VPN connection through QBelt VPN server on QuWAN vRouter.
  • Fixed a user interface string related to online connected clients in the Clients page.
  • Resolved an issue where the host device would disconnect from QuWAN Orchestrator if the web framework of the device malfunctions.
  • Resolved an issue where QuRouter would display the DS-Lite and MAP-E options in the WAN configuration page during the initial router setup process.
  • Fixed an issue where QuRouter would display a service port error message after editing the QBelt QVPN server settings.
  • Previously, QuRouter would fail to update the firmware if the live update method was selected and the router geolocation was set to China.
  • Fixed an issue where QuRouter would display an IP field after selecting PPPoE in the WAN configuration page.
  • Resolved an issue where QuRouter would display a blank dialog box after reconnecting to the WAN connection.
Odpovědět

Kdo je online

Uživatelé prohlížející si toto fórum: Žádní registrovaní uživatelé a 2 hosti